TMC

Cruisin With Cops 3rd Annual Car Show – 5.31.14

In Midwest City Oklahoma (by Tinker Air Force Base) Show is from 10am-2pm and registration starts at 9am. Located at the Reed Center in Midwest City 5800 Will Rogers Rd (I-40 and Sooner Road). Check us out on The Made in Oklahoma website and The City of Midwest City website. All proceeds goes towards the Midwest City Police Explorers and The Special Olympics. Door prizes, music, and 20 vehicle categories. Don’t miss one of the best community Car Shows in the State!!! Contact Sgt. Ron Starcher (405)739-1022.

1999-2013 Truck/SUV Accessory Brackets Item Number: LS-0201

LS-201LS Truck/SUV Alternator Power Steering pump Relocation Bracket
Cost: $299.00  On Sale: $249.99  plus shipping



Designed for the S10,S15 Pickup with LS Truck/Suv Accessory Drive Engine.

Works with any car or truck that needs frame clearance or has steering box issues.

Has been used in follow LS conversion:
All years of S10,S15. S10 front stub in 50,60, Trucks. 1964-77 Chevelle,GM A-body cars including the Malibu,Monte Carlo.
1961-70 Pontiac cars. All cars made from 1964 to 1980. You will need to check measurements on cars before 1963 and after 1980. It should work fine.

I have not had any problems with this design fitting any car or truck.

Detailed Description:

This kit fits 1999 to 2012 GM LS Engine and is a Alternator Power steering pump relocation bracket kit for Gen III/IV LS.
This bracket relocates the Alternator and Power steering pump on the 4.8, 5.3, 5.7, 6.0, and 6.2.
This kit is used when doing a engine swap or building a hot rod and installing a LS1, LS2, LS3, LS6 or any other performance LS car intake manifold on the truck engine to gain hood clearance.
Moves the alternator down 1” inch below the factory ls car intake to clear the hood.
It also moves the Power steering pump up and in to clear the frame and power steering box
LS Brackets design keeps the power steering pump at the correct angle as GM intended it to be
Power steering pump will come from a 1988 to 1989 Chevy pickup. Part number AC Delco (36-517091) pump
You will reuse the factory power steering pulley from the ls truck/suv motor.
You will reuse the factory truck/suv Alternator
This kit also puts everything in a more uniform pattern with the matching a/c bracket so your engine is not lopsided. Just looks better when raising the hood.

When using a Car intake you may need water pump spacer kit LS-0214 and a 1997-02 z28 camaro water pump.
When Install the LS car intake or any other performance intake manifold your throttle body may hit the water neck from the factory truck water pump.
This bracket is to be used with truck accessory drive only
This bracket will relocate your truck alternator to the side and down and your power steering pump in and up to clear the frame and steering box
( 5.5 inch above crank center line )
Comes complete with 6061 Billet Aluminum spacers and plates, GM approved zinc coated bolts and instructions.

  • Items needed to complete the kit:
  • One Idler pulley Gates 36101
  • A new serpentine belt
  • AC Delco 36-517091 power steering pump

Items you can use but are not needed for the kit to work:

This kit will work with the 2010 Camaro water pump and the correct tensioner for the Camaro pump

2010 camaro water pump number AC Delco (251-734 ) No water pump spacers are needed when using this pump.

LS1 camaro water pump
LS-0214 water pump spacers when using ls1 camaro water pump from 98-02 camaro Z28.

LS1,LS6 or any performance intake can be used with this kit.
Note: You must use the correct parts to go along with the intake of your choice.

  • One Idler pulley
  • A new belt
  • AC Delco 36-517091 power steering pump
  • 2010 camaro water pump number AC Delco (251-734 )

No water pump spacers are needed when using this pump.

LS Truck/SUV Alternator Relocation Bracket Item Number: LS-0203

LS Truck/SUV Alternator Relocation Bracket Item Number: LS-0203LS Truck/SUV Alternator Relocation Bracket
Cost: $285.00 
 On Sale: $235.99  plus shipping

Detailed Description:

This alternator relocate bracket is designed to lower your alternator down 3/4 inch below the top of a LS1,LS2,LS3 intake manifold. It will retain the power steering pump in the stock position.
This bracket is made so you can run a LS1,LS2 or any performance LS car intake manifold on the truck or SUV engine to gain hood clearance.
Works on any 4.8,5.3,5.7,6.0,and 6.2 Chevrolet 1999 to 2013 Including Gen III/IV truck engines.
This kit will work with the stock water pump and tensioner. We recommend using a 2002 camaro z28 tensioner
When instaling a car intake you may need to use a 2002 Camaro water pump and LS-0214 spacer kit to clear the throttle body
This bracket will work with the 2010 Camaro water pump and the correct tensioner.
Comes complete with 6061 billet aluminum spacers, two plates, GM spec. zinc coated bolts and instructions
Items needed to complete the kit:
Gates pulley # 36101
Gates belt # K060735
You will need a power steering pump puller and installer. These tools can be rented free from your Auto Zone or O’Reilly.

 

1998-02 LS1 camaro/GTO/S10 LS1 Alternator / Power Steering Pump Bracket

1998-02 LS1 camaroGTOS10 LS1 Alternator Power Steering Pump Bracket1998-02 LS1 camaro/GTO/S10 LS1 Alternator / Power Steering Pump Bracket
Cost: $299.00  On Sale: $249.99  plus shipping




Detailed Description:

This is LS Brackets New State of the art accessory drive power steering/alternator bracket

This bracket is CNC cut from 6061 3/8 billet aluminum

It is designed to work with the Factory Camaro power steering pump and alternator only
The factory Reservoir from the camaro with not fit this bracket.
Requires a Alternator from 1998-02 camaro or 1999 to 2013 Truck/SUV

This is the most user friendly alternator,power steering relocate bracket
on the market today.

This Bracket moves the factory alternator up high and
the factory power steering pump down low on
your LS power plant upgrade.
When using the Camaro crank pulley you gain the needed radiator clearance
for your fans. You will also save money not having to purchase water pump spacer kit
It gives frame clearance in older vehicles where the factory
alternator hits the frame and steering box.
There is a complete set of instructions with part numbers
Everything can be purchased from your local parts store.

Please Email with any question.

Designed to work with the Camaro/Truck/SUV ls 105 amp alternator

Comes complete with 6061 billet aluminum spacers, 3/8 billet plates, GM spec. zinc coated bolts and instructions.

LS TT Turbo Mount Stock Truck Exhaust Item Number: LS-0208

LS TT Turbo Mount Stock Truck Exhaust Item Number LS-0208Item: 1999 to 2013 LS TT Turbo mount Stock Truck exhaust
Cost: $299.00 
 On Sale: $250.99  plus shipping

Detailed Description:

This Bracket is made to work with Front Mount custom built turbo kits Stock 4.8,5.3,6.0 exhaust manifolds with a ls motor You don’t have to buy other exhaust manifolds like other kits.

This kit fits 1999 to 2012 GM Trucks and is a Alternator Power steering pump relocation bracket kit for Gen III/IV LS. This bracket relocates the Alternator and Power steering pump on the 4.8, 5.3, 5.7, 6.0, and 6.2. This kit is used when doing a engine swap or building a hot rod and installing a LS1, LS2, LS3, LS6 or any other performance LS car intake manifold on the truck engine. Moves the alternator down to 3/4 inch below the factory ls car intake to clear the hood.

It also moves the Power steering pump up and in to clear the frame. This kit will let you install any LS 99 to 2012 truck engine into a older car or pickup.

What is really nice about my design is that it reuses the factory LS alternator.

Power steering pump will come from a 1988 to 1989 Chevy pickup. You can reuse your factory pump but must change the can on the back. No more Remote Reservoir to buy a cost saving of over 100.00 and you get a cleaner looking install.

Water pump spacers along with the car intake are required to install the LS car intake or any other performance intake manifold.

This bracket is to be used with truck accessory drive only.

This bracket will relocate your truck alternator to the side and down and your power steering pump in and up to clear the frame.

Comes complete with 6061 billet aluminum spacers, two plates, GM spec. zinc coated bolts and instructions

Items needed to complete the kit:
~Two Idler pulleys
~A new belt
~Car ls1 intake
~Power steering pump-AC Delco 36-517091 ,Atsco 7091,A-1 Cardone 207826,
~Dorman Pulley 300-200
~Dorman cap 82581

This kit will work with the 2010 carmaro water pump and the correct tensioner for the Camaro pump. Water pump (ACDelco 251-734 ) No spacers are needed when use this pump. LS1 camaro water pump. Water pump spacer kit only if your using a 2002 carmaro water pump.

LS LQ4 LS1 Camaro High Mount Alternator Bracket

LS LQ4 LS1 Camaro High Mount Alternator BracketLS LQ4 LS1 Camaro High Mount Alternator Bracket
Cost: $299.00  On Sale: $235.99  plus shipping



Detailed Description:

This relocate bracket is designed to move the 1999 to 02 Camaro factory alternator to the top of the engine.

This kit does raise the factory power steering pump up 1″ higher than normal.

You will reuse your existing power steering pump,Idler pulley and alternator. If you’re having alternator clearance issues this is the bracket you need This kit will work with the stock water pump and tensioner comes complete with 6061 billet aluminum spacers, GM spec. zinc coated bolts and instructions we only use Zinc coated bolts to prevent rust.

Instead of cheap black bolts that will rust over time. The required belt ( Gates K060760 ) 145 amp alternator The required idler pulley if you don’t have your factory one ( Gates 36101 ) Comes with a complete set of instructions and part numbers.

All replacement parts can be bought from your local parts store. All my kits use standard off the shelf parts for easy replacement, another great feature.

Please Email with any question.

This bracket has been dyno tested and I have tons of happy customers Designed to work with all ls Truck/SUV alternators Comes complete with 6061 billet aluminum spacers, 3/8 billet plates GM spec. zinc coated bolts and instructions.

This brackets is also available for the Chevrolet 1999 to 2013 including Gen III/IV truck, LY6,L92 engines accessory drive.

Camaro LS L99 LS3 Alternator Bracket 3/8 Billet

Camaro LS L99 LS3 Alternator Bracket 38 BilletCamaro LS L99 LS3 Alternator Bracket 3/8 Billet
Cost: $299.00  On Sale: $279.99  plus shipping



Detailed Description:

Only a new belt is needed with this kit

When reusing all your factory 2010-13 camaro parts.

Does not come with the pictured A/C Bracket for the Sanden compressor.

This is LS Brackets New State of the art accessory drive power steering, upper alternator mount bracket.

This bracket is CNC cut from 6061 3/8 billet aluminum

It is designed to work with the Factory Camaro power steering pump, Alternator and accessory drive from a 2010-13 camaro

This is the most user friendly alternator,power steering relocate bracket on the market today.

This Bracket moves the factory alternator up high and and keeps the factory engine cover intact.

It gives frame clearance in older vehicles where the factory alternator hits the frame and steering box.

Comes with a complete set of instructions and part numbers

Everything can be purchased from your local parts store.

Please Email with any question.
This bracket has been dyno tested and I have tons of happy customers

Designed to work with the 2010-13 Camaro PS pump and alternator

Comes complete with 6061 billet aluminum spacers, 3/8 billet plates, GM spec. zinc coated bolts and instructions.

This bracket is also 100% compatible with any 5.3,5.7,6.0.6.2 engines using Truck/SUV Crank pulley with 2010-13 camaro accessory drive parts.

Trimming of the factory engine cover maybe needed for best fit.

Crate Engine Narrow Bay Conversion Bracket 3/8 Billet Aluminum

Crate Engine Narrow Bay Conversion Bracket 3/8 Billet AluminumCrate Engine Narrow Bay Conversion Bracket 3/8 Billet Aluminum
Cost: $265.00  On Sale: $229.99  plus shipping


Detailed Description:

This bracket is CNC cut from 6061 3/8 billet aluminum. This kit is for the LS3 or corvette accessory drive only

Can be special ordered for the camaro or Truck/SUV. The power steering pump is the same height as the LS3 intake runners.

It is designed to work with the Factory Camaro power steering pump, Alternator parts from a 1998 to 2002 camaro

This is the most user friendly alternator,power steering relocate bracket on the market today.
This Bracket moves the factory Camaro Power steering pump up 1″

You will need to change the power steering pulley to a Trail Blazer SS Pulley.

This kit is designed to work in 1996 camaro along with any other car or truck.

Kit can be special ordered for Camaro or Truck/SUV accessory drive

Comes with a complete set of instructions and part numbers

Everything can be purchased from your local parts store.

Does not come with the pictured A/C bracket

Please Email with any question.
This bracket has been dyno tested and I have tons of happy customers. Designed to work with the 1998 to 02 Camaro PS pump and alternator

Comes complete with 6061 billet aluminum spacers, 3/8 billet plates, GM spec. zinc coated bolts and instructions.

This bracket is also 100% compatible with any 5.3,5.7,6.0.6.2 engines using Corvette Crank pulley with 1998 to 02 camaro accessory drive parts

Items Needed to complete this Kit:
Power steering pump from a 1998 to 02 camaro
Alternator from a 1998 to 02 camaro or 105 amp from a truck/suv
Idler pulley
New Belt
Trail Blazer SS pulley (Dorman #300137)